Sprinkler-Guard Covers

★★★★★ 4.9 (300+ reviews)
3-inch Sprinkler-Guard Cover - perfect fit for the 3-inch guard
3-inch Sprinkler-Guard Cover - fits the 3-inch guard
Sprinkler-Guard Cover snapped onto the guard
Sprinkler-Guard Cover top view
Sprinkler-Guard Cover underside with sealing tabs
Sprinkler-Guard Cover, flat top
Sprinkler-Guard with cover, top-down view

Sprinkler-Guard Covers

★★★★★ 4.9 (300+ reviews)
$54.99 $2.75 / unit

The snap-on cover that seals over your Sprinkler-Guard and keeps snow, ice, sand, and grit out of the head so it doesn't grind down and fail when the system isn't running.

❄️ All-Climate Seal Made in USA 🎖️ Veteran Owned 5 Star Reviews 300+
10 Pack
$3.00 / unit
$29.99
Most Popular
20 Pack
$2.75 / unit
$54.99
30 Pack
$2.67 / unit
$79.99
Best Value
60 Pack
$2.50 / unit
$149.99
Add to Cart - $54.99
🚚 Free Shipping $100+ Made in Florida

The Sprinkler-Guard Cover is the piece customers kept asking for: a simple, tough cover that snaps over the Sprinkler-Guard and seals the head off from the weather when it's not running. It took over a year to get right. It was tested from below-zero freezing to intense heat, with exterior tabs added so the seal holds whether the material shrinks or expands. In cold climates it keeps snow, hail, and ice out. In sandy, dusty places it keeps sand and grit from getting into the head and grinding it down. Pairs with any Sprinkler-Guard unit.

1

Clear the Grass

Clear the grass 8 to 10 inches around your sprinkler head to make room for the guard.

2

Slide In

Insert the Sprinkler-Guard tube alongside the head and press the disc flush with the ground. The guard should sit slightly above the sprinkler head.

3

Done. You're Protected.

Pack the soil and you're set. For a polished finished look, top it off with a little fish gravel around the sprinkler head.

FitsSnaps onto the Sprinkler-Guard unit
Total Width3 7/8 inches
Height0.5 inch
Protects AgainstSnow, ice, hail, sand & grit
InstallSnaps on in seconds
Tools RequiredNone
Best ForCold climates & sandy/dusty regions
Made InUSA

Free shipping on orders over $100 (excludes Alaska & Hawaii). Most orders ship within 1-2 business days.

★★★★★

What Homeowners Are Saying

4.9 average from 300+ verified reviews

★★★★★
Verified Buyer

"Finally, no more broken heads"

I was replacing 3-4 sprinkler heads every summer. Put these in last spring and haven't replaced a single one since. Best money I've spent on my yard.

Mike R.
Tampa, FL • 20-Pack
Before: 3-4 broken heads/year → After: Zero in 14 months
★★★★★
Verified Buyer

"30 seconds and done"

My wife asked why I was so excited about sprinkler guards. Then I told her how much we spent on repairs last year. She ordered a second pack.

David T.
Phoenix, AZ • 20-Pack
Before: $400/year in repairs → After: $0
★★★★★
Verified Buyer

"Should have done this years ago"

Installed the whole yard in about 20 minutes. The grass was already growing over some of my heads and these stopped that completely. Simple and it works.

Jim K.
Charlotte, NC • 30-Pack
Before: Couldn't find half my heads → After: Every head visible and protected
One ground-down head
$150+
To fix a head fouled by grit or cracked by ice
vs
One cover
~$3
Seals the head off all season
Cheap insurance against ice, sand, and grit.
Simple Installation

Snaps On in Seconds.

Cap your heads before the cold or the dust rolls in. No tools, no hassle.

1

Start With Your Guard

Sprinkler-Guard installed around a sprinkler head

Make sure your Sprinkler-Guard is installed around the head. The cover is designed to seat right on top of it.

2

Snap On the Cover

Sprinkler-Guard pressed flush with the soil around a flush-mount sprinkler head

Press the cover down over the Sprinkler-Guard until the exterior tabs seat and the seal holds.

3

Sealed for the Season

Protected sprinkler head on a beautiful lawn

Snow, ice, sand, and grit stay out of the head. Pop the cover off when you're ready to run the system again.

⏱ Snaps on and off in seconds, no tools
🛡️

All-Climate Seal

Keeps snow, hail, and ice out of your heads through the cold months.

💪

Blocks Sand & Grit

Keeps abrasive sand and grit out so your heads don't grind down and fail. A big deal in dry, dusty regions.

🌿

Snaps On in Seconds

No tools. It snaps right onto your Sprinkler-Guard and pops off just as easily.

🔒

Made in the USA

Over a year of testing and mold work to get the seal right. Veteran-owned.

Common Questions

It snaps over your Sprinkler-Guard and seals the sprinkler head off from the weather when the system isn't running. That keeps snow, ice, hail, sand, and grit out, so the head doesn't grind down or get gummed up.
The cover is designed to snap onto an installed Sprinkler-Guard unit, so it works as part of the system. If you don't have your guards in yet, put those in first and add the covers on top.
That was the hard part. It was tested from below-zero freezing to intense heat, and exterior tabs were added so the seal holds whether the material shrinks or expands with the temperature.
Use them when the system isn't running, like the off-season in cold climates, or any time you want to keep blowing sand and grit out in dry, dusty areas. Pop them off when you're ready to run the sprinklers again.
One cover per sprinkler head you want to protect. Match it to the number of Sprinkler-Guards you've got in the ground.
20 Pack - $55 Free shipping over $100
Add to Cart